新聞中心

聯系我們
聯系我們

蘇州倍徠斯金屬材料制品有限公司

地 址:蘇州工業園區跨塘鎮唯和路93號A棟

聯系人:許志武 
手 機:188 6212 7231
聯系人:潘經理 
手 機:189 1260 8965
聯系人:許經理 
手 機:189 1260 8952


銷售辦:

總機:0512-6829 7075

傳真:0512-6823 6061

銷售處郵箱:jsblessed@163.com

產品詳細

58 58 58

產品名稱: 江蘇12CrNi3A圓鋼 特鋼12CrNi3圓棒價格 12CrNi3合金結構鋼

發布日期: 2016-07-08

點擊數: 1782

二維碼:

簡述: 12CrNi3鋼屬于合金滲碳鋼,比12CrNi2A鋼有更高的淬透性,可以用于制造比12CrNi2A鋼截面稍大的零件。該鋼淬火低溫回火或高溫回火后都具有良好的綜合力學性能,鋼的低溫韌性好,缺口敏感性小,切削加工性能良好,當硬度為HB260~320時,相對切削加工性為60%~70另外,鋼退火后硬度低、塑性好。

產品詳情

12CrNi3鋼屬于合金滲碳鋼,比12CrNi2A鋼有更高的淬透性,因此,可以用于制造比12CrNi2A鋼截面稍大的零件。該鋼淬火低溫回火或高溫回火后都具有良好的綜合力學性能,鋼的低溫韌性好,缺口敏感性小,切削加工性能良好,當硬度為HB260~320時,相對切削加工性為60%~70另外,鋼退火后硬度低、塑性好,因此,既可以采用切削加工方法制造模具,也可以采用冷擠壓成型方法制造模具。為提高模具型腔的耐磨性,模具成型后需要進行滲碳處理,然后再進行淬火和低溫回火,從而保證模具表面具有高硬度、高耐磨性而心部具有很好的韌性,該鋼適宜制造大、中型塑料模具。但該鋼有回火脆性傾向和形成白點的傾向。

特性及適用范圍
是用途較廣的高級滲碳鋼,與15Cr、20Cr鋼相比,其強度、塑性、淬透性均高。主要用來制作重負荷條件下要求高強度,高硬度和高韌性的主軸及要求中心韌性很高或承受沖擊負荷、表面耐磨、熱處理變形小的軸、桿以及在高速和沖擊負荷下工作的各種傳動齒輪、調節螺釘、凸輪軸

化學成份
硅 Si:0.17~0.37
錳 Mn:0.30~0.60
硫 S :允許殘余含量≤0.035
磷 P :允許殘余含量≤0.035
鉻 Cr:0.60~0.90
鎳 Ni:2.75~3.15
銅 Cu:允許殘余含量≤0.030

力學性能
抗拉強度 σb (MPa):≥930(95)
屈服強度 σs (MPa):≥685(70)
伸長率 δ5 (%):≥11
斷面收縮率 ψ (%):≥50
沖擊功 Akv (J):≥71
沖擊韌性值 αkv (J/cm2):≥88(9)
硬度 :≤217HB
試樣尺寸:試樣毛坯尺寸為15mm
●熱處理規范及金相組織:
熱處理規范:淬火:第一次860℃,第二次780℃,油冷;回火200℃,水冷、空冷。

●交貨狀態:以熱處理(正火、退火或高溫回火)或不熱處理狀態交貨,交貨狀態應在合同中注明。


12CrNi3 steel is alloyed with carbon steel, which has a higher quenching property than 12CrNi2A steel. Therefore, it can be used to manufacture parts that are slightly larger than the 12CrNi2A steel. The hardened steel tempered at low temperature or high temperature tempering after has good comprehensive mechanical properties and good low temperature toughness of the steel, the small notch sensitivity, good cutting properties. When the hardness is HB260 to 320, relative machinability is 60% ~ 70 also low hardness of steel after annealing, good plasticity. Thus, the utility model can by cutting machining method to manufacture the mold, can also be used in cold extrusion molding method for manufacturing mold. In order to improve the wear resistance of the mold cavity, the mold needs for carburization, and then quenched and tempered at low temperature, so as to ensure the mold surface with high hardness, high wear resistance and heart department has a very good toughness, the steel suitable large and medium-sized plastic mold manufacturing. But the steel temper brittleness tendency and the formation of white spots.
Characteristic and applicable scope
It is widely used in high - carbon steel, compared with 15Cr and 20Cr steel, the strength, plasticity and quenching of the high - carbon steel are high. Mainly used to produce high strength requirements under the condition of heavy load, high hardness and high toughness of spindle and center toughness is high or under impact load, surface abrasion resistance, heat treatment deformation small shaft, rod and under high speed and impact load of various transmission gear, adjusting screw, a cam shaft
Chemical composition
Silicon Si:0.17 ~ 0.37
Mn Mn:0.30 ~ 0.60
S: allow residual sulfur content less than 0.035
P P: allow residual content less than 0.035
Chrome Cr:0.60 ~ 0.90
Nickel Ni:2.75 ~ 3.15
Cu: allow residual copper content is less than 0.030
Mechanical properties
The ultimate tensile strength of B (MPa): 930 (95)
Yield strength s (MPa): 685 (70)
5 elongation (%): 11
Section shrinkage (%): 50 psi
The impact of Akv (J): 71
The impact toughness value of alpha kV (J/cm2): 88 (9)
Hardness: 217HB
Sample size: the sample size is 15mm
The specification of heat treatment and microstructure:
Heat treatment specification: quenching: the first 860, 780 second, oil cooling, tempering 200, water cooling, air cooling.
] delivery status: to heat treatment (normalizing, annealing or tempering) with or without heat treatment delivery, delivery status should be indicated in the contract.

江蘇蘇州倍徠斯金屬供應東北撫順特鋼12CrNi3A圓鋼,大冶特鋼12CrNi3A圓棒,重特12CrNi3A價格,上海寶鋼12CrNi3鍛圓,浙江12CrNi3鍛造圓鋼,哪里有賣12CrNi3鍛件?12CrNi3是什么材料?批發零售12CrNi3供應商——蘇州倍徠斯金屬。

 

版權所有:蘇州倍徠斯金屬材料制品有限公司 備案號:蘇ICP備15026697號

友情鏈接:蘇州倍徠斯金屬材料制品有限公司  蘇州倍徠斯金屬材料制品有限公司

1
許先生
3
潘經理
4
許經理
在線客服